![]() The Ice comes in two versions, Standard (8S) which is optimized for demanding RC heli and sport aircraft applications and a Lite (6S) packaged in heat shrink for users with tight fuselages. All Phoenix Ice are ready to fly out of the bag, no programming is necessary for most aircraft applications. The controllers are set at the factory for Auto Lipo detect/cutoff operation and they are tuned for optimum outrunner performance. Heli users are raving about the performance of Castle's programmable helicopter modes which include options to directly enter desired governed head speeds as numerical values! Castle Creations Phoenix Ice 100 ManualThis is the Phoenix Edge 75 Amp Electronic Speed Control from Castle Creations. Every heli power combination requires slightly varying governor gains, Castle makes these easy to tweak and the net result is a rock solid tail. Advanced users will find the incredible programmability of the Phoenix Ice allows for performance characteristics tailored exactly to their desires. Switching BEC The Phoenix Ice switching BEC output is factory set to 5V. Users may use Castle Link to select their desired voltage between 5V and 7V, in 0.1V increments. Data Logging Ice brings another incredibly useful feature, extensive data logging capabilities. The controllers are able to measure and record many parameters at sample rates that you choose between 10 samples per second and 1 sample per second. This data is stored directly in the controller and may be accessed once the run is over using the Castle Link USB adapter (sold separately) and Castle Link software (available free at castlecreations.com). The Max Log Size is 21,504 bytes, everything takes one byte except for motor rpm which takes two. Castle Creation ICE data logging feature: - Battery Voltage, Ripple and Current - Controller Temperature - Controller Input Throttle - Controller Motor Power Output - Motor RPM Phonix ICE ECS - Data Logging Screen: Phonix ICE ECS - Helicopter Programming Screen. I’ve received a ton of inquires about the iKon internal gov and it seems to be a bit of a confusion when it comes to the setup. I’ve included some step-by-step procedures here for setting up the iKon internal governor with a Castle Creations ESC and a Scorpion ESC. The Scorpion would should apply ver similarly to other non-CC ESC’s as Castle is the only brand that you need to match the endpoints in the iKon with what the CC ESC wants to see. All others are taught the endpoints. IKon electric gov w/CC ESC and autorotation bailout Heli Setup: Main and tail blades removed or motor backed away from pinion Radio Setup: Throttle curves as follows. Normal- 0,30,30,30,100, Idle 1 flat 60, Idle 2 flat 100 Throttle Hold 0% CC ESC Setup: Ext Gov mode enabled Headspeed change rate set to 20 For EDGE controllers make sure the AUX wire is set to external RPM mode Leave soft start at default value Check the Enable Autorotation Bailout box Program any of your motor specs as per factory recommendations iKon Setup: Open up the iKon software, iKon plugged in and powered, radio on, ESC off Basic Menu-Transmitter Setup: Make sure you get 0% throttle and 100% throttle on the iKon when moving the throttle stick up and down. If not adjust radio endpoints on throttle channel to match Basic Menu-Flying Style Setup: Check the Use Governor box in all three banks Click View (top left of iKon software) then click Advanced. This will further be called the Advanced Menu Advanced Menu-Common-Governor-Setup: Input your gear ratio Sensing Divisor: Motor poles/2. *For example in my case most of mine are 5 Throttle Min: temporarily put at approx 1100. Throttle Max temporarily put at 2000 Advanced Menu-Common-Governor-Speeds: Input your three desired head speeds Advanced Menu-Common-Governor-Gains: Check the Motor is Electric box Leave all the gains at the factory values. This should be a P gain of 50. Can be checked in the Basic Menu under the governor tab as well. Gov gain will be 50 Advanced Menu-Common-Governor-Spoolup: Ramp Up and Ramp Down set to 15 Spoolup Ramp: 3 Deadzone: 100 Leave Bailout Timout and Bailout Ramp at zero as we’ll be using the CC autorotation bailout Endpoints Programming/Throttle Hold calibration: **Note: We will be spooling the heli up during these steps so be aware** Radio On. Throttle at high stick in Normal mode. Throttle hold off iKon is powered and plugged into PC. Advanced Menu-Common-Governor-Setup is up on the screen Plug in ESC and listen (Di,di,di,di,di). Number of tones will depend on cell count but what you’re listening for is that there all the same tone. Newby was brought to the Bluegrass state by the University of Kentucky where he was accepted into the Oral and Maxillofacial Surgery program. After dental school, Dr. Observership programs in chicago. Newby is a graduate of the University Of Kentucky College Of Medicine and is currently in his Chief year in Oral and Maxillofacial Surgery. This means that the ESC is powered up but is NOT armed yet. NOTE: If you have an internal BEC and are powering the iKon with that then steps 2-4 will be combined all into on step. Slowly increase the Throttle Max slider in the iKon software until the ESC beeps and there is a red light that will blink. Castle Creations Phoenix Ice 100 ManualsThrottle high is now calibrated. Unplug ESC Throttle at Low stick now. Throttle hold off Plug in ESC and listen (di,di,di,di,di) All tones should be the same indicating the ESC is NOT armed. Slowly decrease the Throttle Min slider until the ESC beeps (di,do). *Note: ESC is now armed and can be spooled up* Leave ESC powered up. Throttle at low stick. Go into Throttle Hold menu in radio. With Throttle Hold switch ON slowly increase throttle hold percentage in the radio until the motor starts to spool up. Through the use of MOAC MTA titles you can help ensure your students future success in and out of the classroom. Software development fundamentals exam 98-361 ebook download. The MTA program curriculum helps instructors teach and validate fundamental technology concepts and provides students with a foundation for their careers as well as the confidence they need to succeed in advanced studies. Back it back down until it stops then go one point lower. Unplug ESC Go back into your radio and drop the last point on your Normal Mode throttle curve back down to 30 You’re done! Verification: No PC software hooked up. Throttle hold ON Plug in ESC and listen. (di,di,di,di,di) Heli can now be transported to the flight line safely as the ESC is not armed yet. Castle Creations Phoenix Ice 100 Manual 2017With the Radio at low stick flip out of Throttle Hold Sound of (di,do) should be heard. ESC is now armed and ready for flight. Note: *There is still an occasional 1-2 second delay for spool up to start on the CC ESC’s. This is a glitch in the iKon firmware and doesn’t affect anything in a negative way so if you experience a slight delay don’t worry.* Autorotation bailout will function as normal CC autorotation bailout does. To disable the bailout and re-engage soft start you have to land, go back into normal mode, and low stick. That will reset the soft start. IKon electric gov w/Scorpion ESC and autorotation bailout Heli Setup: Main and tail blades removed or motor backed away from pinion Radio Setup: Throttle curves as follows. Download proshow producer 6. Normal- 0,30,30,30,100, Idle 1 flat 60, Idle 2 flat 100 Throttle Hold 0% Scorpion Setup: External Governor Mode Timing to 5* for most motors iKon Setup: Open up the iKon software, iKon plugged in and powered, radio on, ESC off Basic Menu-Transmitter Setup: Make sure you get 0% throttle and 100% throttle on the iKon when moving the throttle stick up and down. If not adjust radio endpoints on throttle channel to match Basic Menu-Flying Style Setup: Check the Use Governor box in all three banks Click View (top left of iKon software) then click Advanced.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |